Pearl Bar Inc., DBA Chairs

Food properly labeled; original container — Inspector Note: Observed multiple large squeeze bottles holding condiments and sauces without proper labels stored throughout cook line in kitchen. CA: Kitchen team member properly labeled all squeeze bottles during inspection. 511-6-1.04(4)(d) - Food Storage Containers Identified with Common Name of Food (C) (d) Food Storage Containers, Identified with Common Name of Food. Except for containers holding food that can be readily and unmistakably recognized, such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be clearly and legibly identified, in English, with the common name of the food.

In-use utensils: properly stored — Inspector Note: Observed multiple pairs of tongs stored on oven door handles in kitchen. Operator removed tongs and properly stored during inspection. 511-6-1.04(4)(k) - In-Use Utensils, Between-Use Storage (C) (k)Storage of In-Use Utensils. During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: 1.Except as specified under paragraph 2 of this subsection, in the food with their handles above the top of the food and the container; 2.In food that is not time/temperature control for safety food with their handles above the top of the food within containers or equipment that can be closed, such as bins of sugar, flour, or cinnamon; 3.On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized at a frequency specified under DPH Rule 511-6-1-.05(7)(b) and (8)(a);

Nonfood-contact surfaces clean — Inspector Note: Observed reach in freezer shelves, ric gaskets soiled with food debris accumulation throughout kitchen. Observed shelving rusted within walk in cooler. Operator instructed to properly clean and sanitize all non food contact surfaces during inspection. 511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

Nonfood-contact surfaces clean — Inspector Note: Observed reach in freezer shelves, ric gaskets soiled with food debris accumulation throughout kitchen. Operator instructed to properly clean and sanitize all non food contact surfaces during inspection. 511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

Physical facilities installed, maintained, and clean — Inspector Note: Observed paint peeling on ceilings and walls inside kitchen. Observed dirty walls throughout kitchen. Observed floor tiles cracked throughout walk in cooler within kitchen. Must clean and repair within 10 days. 511-6-1.07(2)(a) - Floor, Walls, & Ceilings, Cleanability (C) (2) Design, Construction, and Installation. (a) Floors, Walls, and Ceilings, Cleanability. Except as specified under subsection (2)(d) of this Rule and except for antislip floor coverings or applications that may be used for safety reasons, floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed, and installed so they are smooth and easily cleanable.

Adequate ventilation and lighting; designated areas used — Inspector Note: Observed low light levels provided in walk in cooler in kitchen. Operator instructed to correct within 10 days during inspection. 511-6-1.07(3)(f) - Lighting Intensity, adequate in food prep, storage & service areas (C) (f) Lighting Intensity. The light intensity shall be: 1. At least 10 foot candles (108 lux) at a distance of 30 inches (75 cm) above the floor, in walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning; 2. At least 20 foot candles (215 lux): (i) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption; (ii) Inside equipment such as reach-in and under-counter refrigerators;

In-use utensils: properly stored — Inspector Note: Observed multiple pairs of tongs stored on oven door handles in kitchen. Operator removed tongs and properly stored during inspection. 511-6-1.04(4)(k) - In-Use Utensils, Between-Use Storage (C) (k)Storage of In-Use Utensils. During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: 1.Except as specified under paragraph 2 of this subsection, in the food with their handles above the top of the food and the container; 2.In food that is not time/temperature control for safety food with their handles above the top of the food within containers or equipment that can be closed, such as bins of sugar, flour, or cinnamon; 3.On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized at a frequency specified under DPH Rule 511-6-1-.05(7)(b) and (8)(a);

Nonfood-contact surfaces clean — Inspector Note: Observed reach in cooler shelves, gaskets, exterior doors and door handles soiled with food debris accumulation throughout kitchen. Operator instructed to properly clean and sanitize all non food contact surfaces during inspection. 511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

Adequate ventilation and lighting; designated areas used — Inspector Note: Observed low light levels provided in walk in cooler in kitchen. Operator instructed to correct within 7 days during inspection. 511-6-1.07(3)(f) - Lighting Intensity, adequate in food prep, storage & service areas (C) (f) Lighting Intensity. The light intensity shall be: 1. At least 10 foot candles (108 lux) at a distance of 30 inches (75 cm) above the floor, in walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning; 2. At least 20 foot candles (215 lux): (i) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption; (ii) Inside equipment such as reach-in and under-counter refrigerators;

Proper date marking and disposition — Inspector Note: -Observed chicken salad without date labeled stored in lowboy cooler across from cook line in kitchen. Operator states chicken salad prepared on Monday 3/9/26. Operator properly labeled container. -Observed sautéed Brussels sprouts without date labeled stored in lowboy cooler across from cook line in kitchen. Operator states Brussel sprouts prepared on Wednesday 3/11/26. Operator properly labeled container. 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking 1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 5 and 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf 2. Except as specified in paragraphs 5 through 7 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf 3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf 4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include: (i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine; (ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; (iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or (iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request.

Toxic substances properly identified, stored, used — Inspector Note: Observed spray bottle holding pine cleaner without label stored in crate next to dish machine in kitchen. Operator labeled spray bottle during inspection. 511-6-1.07(6)(b) - Working Containers, Common Name (Pf) (b) Working Containers, Common Name. Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. Pf