Little 5 Pub

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed cutting boards on the preptop coolers that were stained and had gashes. CA- cutting boards shall be resurfaced if unable to be cleaned. 511-6-1.05(6)(b) - Cutting Surfaces (C) (b) Cutting Surfaces. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced.

Nonfood-contact surfaces clean — Inspector Note: Observed the RIF in the main kitchen unclean with debris at the bottom. CA- PIC started to take out items in the freezer to have an employee clean the bottom. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. 3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Adequate handwashing facilities supplied & accessible — Inspector Note: Observed ice dumped in the hand sink in the bar area. COS- ice was removed from the sink and PIC was told they cannot dump in the hand sink. 511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink. 1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf 2. A handwashing facility may not be used for purposes other than handwashing. Pf

Proper cooling methods used: adequate equipment for temperature control — Inspector Note: Observed chicken wings being cooled at room temperature. COS- chicken wings were cooled on an ice bath. 511-6-1.04(6)(e) - Cooling Methods (Pf, C) (e) Cooling Methods. 1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled: (i) Placing the food in shallow pans; Pf (ii) Separating the food into smaller or thinner portions; Pf (iii) Using rapid cooling equipment; Pf (iv) Stirring the food in a container placed in an ice water bath; Pf (v) Using containers that facilitate heat transfer; Pf (vi) Adding ice as an ingredient; Pf or (vii) Other effective methods. Pf 2. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (i) Arranged in the equipment to provide maximum heat transfer through the container walls; and (ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food.

Approved thawing methods used — Inspector Note: Observed two different kinds of fish thawing in the vacuum packaging in the WIC. Both packages of fish beared a warning label stating fish to be removed from package prior to thawing. COS- fish was removed from the packaging. 511-6-1.04(6)(c) - Thawing (C) (c) Thawing. Except as specified in paragraph 4 of this subsection, time/temperature control for safety food shall be thawed: 1. Under refrigeration that maintains the food temperature at 41°F (5°C) or less; PF or 5. Reduced oxygen packaged fish that bears a label indicating that it is to be kept frozen until time of use shall be removed from the reduced oxygen environment: (i) Prior to its thawing under refrigeration that maintains the food temperature at 41°F (5°C) or less; or (ii) Prior to, or immediately upon completion of its thawing, using procedures to completely submerge in running water as specified in paragraph 2 of this subsection.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed cutting boards on the preptop coolers that were stained and had gashes. CA- cutting boards shall be resurfaced if unable to be cleaned. 511-6-1.05(6)(b) - Cutting Surfaces (C) (b) Cutting Surfaces. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced.