Taco Bell, KFC

Thermometers provided and accurate — Inspector Note: Observed no thermometer in reach-in cooler or walk-in cooler.

Contamination prevented during food preparation, storage, display — Inspector Note: Observed sanitizer bucket stored next to tacos. 511-6-1.04(4)(q) - Food Storage (C) (q) Food Storage. 1. Except as specified in paragraphs 2 and 3 of this subsection, food shall be protected from contamination by storing the food: (i) In a clean, dry location; (ii) Where it is not exposed to splash, dust, or other contamination; and (iii) At least 6 inches (15 cm) above the floor. 2. Food in packages and working containers may be stored less than 6 inches (15 cm) above the floor on case lot handling equipment if the equipment can be moved by hand or by conveniently available apparatuses such as hand trucks and forklifts. 3. Pressurized beverage containers, cased food in waterproof containers such as bottles or cans, and milk containers in plastic crates may be stored on a floor that is clean and not exposed to floor moisture.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Shelf used to store fryer baskets observed with paint peeling on the preparation line. PIC will replace the rack by 6/15/2026. Also observed the cabinet doors below the drink station in bad repair. Doors falling off the hinges. Interior of doors in bad repair as well. PIC will have the cabinet doors repaired by 6/15/2026. Observed a hole in the mop sink. Also observed a bin in the walk in cooler in bad repair. 511-6-1.05(2)(c) - Multiuse Food-Contact Surfaces (Pf) (c) Multiuse Food-Contact Surfaces. 1. Multiuse food-contact surfaces shall be: (i) Smooth; Pf (ii) Free of breaks, open seams, cracks, chips, inclusions, pits, and similar imperfections; Pf (iii) Free of sharp internal angles, corners, and crevices; Pf (iv) Finished to have smooth welds and joints; Pf and (v) Except as specified in paragraph 2 of this subsection, accessible for cleaning and inspection by one of the following methods: (I) Without being disassembled, Pf (II) By disassembling without the use of tools, Pf or (III) By easy disassembling with the use of handheld tools commonly available to maintenance and cleaning personnel such as screwdrivers, pliers, open-end wrenches, and Allen wrenches. Pf 2. The requirement in paragraph 1(v) of this subsection does not apply to cooking oil storage tanks, Distribution lines for cooking oils, or beverage syrup lines or tubes.

Adequate ventilation and lighting; designated areas used — Inspector Note: Observed an employee bag stored with clean dishes. PIC corrected on site by relocating the employee bag. 511-6-1.07(4)(b) - Designated Areas for Employee Activity, located to prevent contamination of food, equipment, utensils, linens, & single service articles (C) (b) Designated Areas for Employee Activity. 1. Areas designated for employees to eat, drink, use tobacco products and electronic devices shall be located so that food, equipment, linens, and single-service and single-use articles are protected from contamination. 2. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens and single-service and single-use articles cannot occur.

Utensils, equipment and linens: properly stored, dried, handled — Inspector Note: Observed dishes stacked by the 3-compartment sink with water nesting in them. The dishes will need to be properly air dried on the drain boards or the shelf above the 3-comapartment sink then stored on the clean dishes shelf once dried. 511-6-1.05(10)(a) - Equipment & Utensils, Air-Drying Required (C) (10) Protection of Clean Items. (a) Equipment and Utensils, Air-Drying Required. After cleaning and sanitizing, equipment and utensils: 1. Shall be air-dried or used after adequate draining before contact with food; and 2. May not be cloth dried except that utensils that have been air-dried may be polished with cloths that are maintained clean and dry.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed the lid on the coleslaw in the walk in cooler cracked. PIC stated that new containers has been ordered for the facility. 511-6-1.05(2)(c) - Multiuse Food-Contact Surfaces (Pf) (c) Multiuse Food-Contact Surfaces. 1. Multiuse food-contact surfaces shall be: (i) Smooth; Pf (ii) Free of breaks, open seams, cracks, chips, inclusions, pits, and similar imperfections; Pf (iii) Free of sharp internal angles, corners, and crevices; Pf (iv) Finished to have smooth welds and joints; Pf and (v) Except as specified in paragraph 2 of this subsection, accessible for cleaning and inspection by one of the following methods: (I) Without being disassembled, Pf (II) By disassembling without the use of tools, Pf or (III) By easy disassembling with the use of handheld tools commonly available to maintenance and cleaning personnel such as screwdrivers, pliers, open-end wrenches, and Allen wrenches. Pf 2. The requirement in paragraph 1(v) of this subsection does not apply to cooking oil storage tanks, Distribution lines for cooking oils, or beverage syrup lines or tubes.

Nonfood-contact surfaces clean — Inspector Note: Observed an accumulation of old food and black build up on the push cart (shelf) in the walk in cooler. Also, an accumulation of old food build up in the bottom of the reach in freezer on the raw chicken line. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. 3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Nonfood-contact surfaces clean — Inspector Note: Observed the blowers/vents in the raw chicken walk in cooler in need of cleaning due to build up. 511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

Adequate ventilation and lighting; designated areas used — Inspector Note: Observed the light shield (fixture) in the men's restroom hanging. Advised PIC to repair the fixture so that it will not fall down. 511-6-1.07(2)(i) - Light Bulbs, Protective Shielding (C) (i) Light Bulbs, Protective Shielding. 1. Except as specified in paragraph 2 of this subsection, light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food; clean equipment, utensils, and linens; or unwrapped single-service and single-use articles. 2. Shielded, coated, or otherwise shatter-resistant bulbs need not be used in areas used only for storing food in unopened packages, if: (i) The integrity of the packages cannot be affected by broken glass falling onto them; and (ii) The packages are capable of being cleaned of debris from broken bulbs before the packages are opened. 3. An infrared or other heat lamp shall be protected against breakage by a shield surrounding and extending beyond the bulb so that only the face of the bulb is exposed.