Waffle House #1587

Contamination prevented during food preparation, storage, display — Inspector Note: Observed single serving butters stored in stagnant water at bottom of reach-in cooler and exposed to splash from leaking refrigeration unit. 511-6-1.04(4)(q) - Food Storage (C) (q) Food Storage. 1. Except as specified in paragraphs 2 and 3 of this subsection, food shall be protected from contamination by storing the food: (i) In a clean, dry location; (ii) Where it is not exposed to splash, dust, or other contamination; and (iii) At least 6 inches (15 cm) above the floor. 2. Food in packages and working containers may be stored less than 6 inches (15 cm) above the floor on case lot handling equipment if the equipment can be moved by hand or by conveniently available apparatuses such as hand trucks and forklifts.

Wiping cloths: properly used and stored — Inspector Note: Observed wiping cloths stored in chlorine sanitizer solution below proper minimum concentration. Employee remade sanitizer solution. 511-6-1.04(4)(m) - Wiping Cloths, Use Limitation (C) (m) Wiping Cloths, Use Limitation. 1. Cloths in-use for wiping food spills from tableware and carry-out containers that occur as food is being served shall be: (i) Maintained dry; and (ii) Used for no other purpose. 2. Cloths in-use for wiping counters and other equipment surfaces shall be: (i) Held between uses in a chemical sanitizer solution at a concentration specified under DPH Rule 511-6-1-.05(6)(n); and (ii) Laundered daily. 3. Cloths in-use for wiping surfaces in contact with raw animal foods shall be kept separate from cloths used for other purposes. 4. Dry wiping cloths and the chemical sanitizing solutions in which wet wiping cloths are held between uses shall be free of food debris and visible soil. 5. Containers of chemical sanitizing solutions in which wet wiping cloths are held between uses shall be stored off the floor and used in a manner that prevents contamination of food, equipment, utensils, linens, single-service, or single-use articles. 6. Single-use disposable sanitizer wipes shall be used in accordance with EPA-approved manufacturer’s label use instructions.

Posted: Permit/Inspection/Choking Poster/Handwashing — Inspector Note: Observed no inspection report posted within the facility. 511-6-1.02(1)(d) - Displaying of the Inspection Report (C) 1. The most current inspection report shall be prominently displayed in public view at all times, within fifteen feet of the front or primary public door and between five feet and seven feet from the floor and in an area where it can be read at a distance of one foot away. 2. Food service establishments with drive-thru windows will post the current inspection report, and also have the inspection report posted so that a minimum of the top one-third of a copy of the current inspection report is visible through each window allowing customers to easily read the score, date of inspection and establishment information. 3. At food service establishments with no primary or public door, the current inspection report shall be prominently displayed at all times where the documents can be read by the public from a distance of one foot away. If requirements of this paragraph are not possible because of physical restrictions, a location will be determined as approved by the Health Authority. 4. The most current inspection report for mobile food service units and extended food service units issued by the local Health Authority having jurisdiction for its inspections shall be prominently displayed in public view during all hours of operation. Such inspection reports shall be prominently displayed at the point of service where the documents can be read by the public from a distance of one foot away. 5. A food service establishment inspection report addendum need not be displayed, but shall be made available by the food service establishment to the public upon request.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed melted handles of knives at prep-top cooler. Manager was advised to discard of items. 511-6-1.05(2)(a) - Equipment and Utensils, constructed of durable materials (C) (2) Design and Construction. (a) Equipment and Utensils. Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions.

Plumbing installed; proper backflow devices — Inspector Note: Observed reach-in cooler refrigeration unit leaking. 511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair.

Insects, rodents, and animals not present — Inspector Note: Observed back door of the facility with gaping. Manager was advised to properly seal back door. 511-6-1.07(2)(m) - Outer Openings Protected (C) (m) Outer Openings, Protected. 1. Except as specified in paragraphs 2 through 5 of this subsection, outer openings of a food service establishment shall be protected against the entry of insects and rodents by: (i) Filling or closing holes and other gaps along floors, walls, and ceilings; (ii) Closed, tight-fitting windows; and (iii) Solid, self-closing, tight-fitting doors. 2. The requirements in paragraph 1 of this subsection does not apply if a food service establishment opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents. 3. Exterior doors used as exits need not be self-closing if they are: (i) Solid and tight-fitting; (ii) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the food establishment; and (iii) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use. 4. Except as specified in paragraphs 2 and 5 of this subsection, if the windows or doors of a food service establishment, or of a larger structure within which a food service establishment is located, are kept open for ventilation or other purposes or a temporary food service establishment is not provided with windows and doors as specified under paragraph 1 of this subsection, the openings shall be protected against the entry of insects and rodents by: (i) 16 mesh to 1 inch (16 mesh to 25.4 mm) screens; (ii) Properly designed and installed air curtains to control flying insects; or (iii) Other effective means. 5. The requirement in paragraph 4 of this subsection does not apply if flying insects and other pests are absent due to the location of the establishment, the weather, or other limiting condition.

Food-contact surfaces: cleaned & sanitized — Inspector Note: Observed dish machine not reach proper sanitization temperature. At time of inspection maintenance began the repairs of dish machine. Manager was advised to discontinue use until machine was fixed. 511-6-1.05(6)(l) - Mechanical Warewashing, Hot Water Sanitization Temperatures(P) (l) Mechanical Warewashing Equipment, Hot Water Sanitization Temperatures. 1. Except as specified in paragraph 2 of this subsection, in a mechanical operation, the temperature of the fresh hot water sanitizing rinse as it enters the manifold may not be more than 194ºF (90ºC), or less than: Pf (i) For a stationary rack, single temperature machine, 165ºF (74ºC); Pf or (ii) For all other machines, 180ºF (82ºC). Pf 2. The maximum temperatures specified under paragraph 1 of this subsection, do not apply to the high pressure and temperature systems with wand-type, hand-held, spraying devices used for the in-place cleaning and sanitizing of equipment such as meat saws

Food-contact surfaces: cleaned & sanitized — Inspector Note: Observed dishes in drawer under grill with food accumulation. Manager was advised to place items to be properly cleaned and sanitized. 511-6-1.05(7)(a)1 - Equipment, Food-Contact Surfaces,& Utensils (Pf) (7) Cleaning of Equipment and Utensils. (a) Equipment, Food-Contact Surfaces, and Utensils. 1. Equipment food-contact surfaces and utensils shall be clean to sight and touch. Pf.

Proper cold holding temperatures — Inspector Note: Observed multiple TCS food items stored in reach-in coolers and prep-top coolers above 41F. Manager disposed of items. 511-6-1.04(6)(f) - Time/Temperature Control for Safety; Cold Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P

Posted: Permit/Inspection/Choking Poster/Handwashing — Inspector Note: Observed the inspection report not posted within 15 feet of the front door, 5-7 feet from the floor, and within one foot of reading distance. The report was posted 2-3 feet from the floor in the hallway leading to the restroom.

In-use utensils: properly stored — Inspector Note: Observed the ice scoop handle stored in ice. The ice scoop handle was located in the ice bin. PIC corrected on site by properly storing the ice scoop in the ice scoop holder. 511-6-1.04(4)(k) - In-Use Utensils, Between-Use Storage (C) (k)Storage of In-Use Utensils. During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: 1.Except as specified under paragraph 2 of this subsection, in the food with their handles above the top of the food and the container; 2.In food that is not time/temperature control for safety food with their handles above the top of the food within containers or equipment that can be closed, such as bins of sugar, flour, or cinnamon; 3.On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized at a frequency specified under DPH Rule 511-6-1-.05(7)(b) and (8)(a); 4.In running water of sufficient velocity to flush particulates to the drain, if used with moist food such as ice cream or mashed potatoes; 5. In a clean, protected location if the utensils, such as ice scoops, are used only with a food that is not time/temperature control for safety food; or 6. In a container of water if the water is maintained at a temperature of at least 135°F (57°C) and the container is cleaned at a frequency specified under DPH Rule 511-6-1-.05(7)(b)3(vi).

Utensils, equipment and linens: properly stored, dried, handled — Inspector Note: Observed pans wetnesting in the cabinet storage area beneath the coffee machine. Observed bowls not inverted above the grits storage/steam table area. Also observed plates not inverted above the grill area. PIC advised that he received an internal memo stating that plates do not have to be inverted.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed the cutting board in bad repair above the three compartment sink. PIC advised the cutting board is used for onions. The cutting board is beginning to chip on both sides. As a result, the PIC discarded the cutting board. Also observed the interior of the Cambro used for hot holding in bad repair. Observed exposed insulation in the interior wall of the unit. PIC advised to cease using the cambro due to potential contamination. 511-6-1.05(2)(c) - Multiuse Food-Contact Surfaces (Pf) (c) Multiuse Food-Contact Surfaces. 1. Multiuse food-contact surfaces shall be: (i) Smooth; Pf (ii) Free of breaks, open seams, cracks, chips, inclusions, pits, and similar imperfections; Pf (iii) Free of sharp internal angles, corners, and crevices; Pf (iv) Finished to have smooth welds and joints; Pf and (v) Except as specified in paragraph 2 of this subsection, accessible for cleaning and inspection by one of the following methods: (I) Without being disassembled, Pf (II) By disassembling without the use of tools, Pf or (III) By easy disassembling with the use of handheld tools commonly available to maintenance and cleaning personnel such as screwdrivers, pliers, open-end wrenches, and Allen wrenches. Pf 2. The requirement in paragraph 1(v) of this subsection does not apply to cooking oil storage tanks, Distribution lines for cooking oils, or beverage syrup lines or tubes. 511-6-1.05(1)(i) - Nonfood-contact Surfaces (C) (i) Nonfood-contact Surfaces. Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material.

Physical facilities installed, maintained, and clean — Inspector Note: Observed an accumulated mold like substance from old food debris on the ceiling of the walk in cooler. PIC will have the ceiling cleaned by 12/12/25

Adequate ventilation and lighting; designated areas used — Inspector Note: Observed employee food (Chicken tenders) stored in the cambro used for hot holding in the back of house.

Insects, rodents, and animals not present — Inspector Note: Observed back door of the facility not tightly fitting. The back door is not properly sealed causing the outer openings to not be protected. PIC is aware that the back door must be sealed. PIC will have the back door sealed by 12/15/25. 511-6-1.07(2)(m) - Outer Openings Protected (C) (m) Outer Openings, Protected. 1. Except as specified in paragraphs 2 through 5 of this subsection, outer openings of a food service establishment shall be protected against the entry of insects and rodents by: (i) Filling or closing holes and other gaps along floors, walls, and ceilings; (ii) Closed, tight-fitting windows; and (iii) Solid, self-closing, tight-fitting doors. 2. The requirements in paragraph 1 of this subsection does not apply if a food service establishment opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents. 3. Exterior doors used as exits need not be self-closing if they are: (i) Solid and tight-fitting; (ii) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the food establishment; and (iii) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use. 4. Except as specified in paragraphs 2 and 5 of this subsection, if the windows or doors of a food service establishment, or of a larger structure within which a food service establishment is located, are kept open for ventilation or other purposes or a temporary food service establishment is not provided with windows and doors as specified under paragraph 1 of this subsection, the openings shall be protected against the entry of insects and rodents by: (i) 16 mesh to 1 inch (16 mesh to 25.4 mm) screens; (ii) Properly designed and installed air curtains to control flying insects; or (iii) Other effective means. 5. The requirement in paragraph 4 of this subsection does not apply if flying insects and other pests are absent due to the location of the establishment, the weather, or other limiting condition.

Proper eating, tasting, drinking, or tobacco use — Inspector Note: Open employee water bottles stored next to single service articles in the back of house. Also observed employee's food (Chicken Tenders) stored in cambro used for hot holding grits. PIC corrected on site.

Adequate handwashing facilities supplied & accessible — Inspector Note: Observed paperwtowels and/or hand drying devices not provided at the hand sink in the back of house.

Toxic substances properly identified, stored, used — Inspector Note: Observed degreaser stored and other chemical bottles stored with straws in the back of house