Dairy Queen Grill & Chill

Personal cleanliness — Inspector Note: Observed several employee preparing food in the back of house not wearing proper hair restraints. 511-6-1.03(5)(g) - Jewelry (C) (g) Jewelry. Except for a plain ring such as a wedding band food employees may not wear jewelry including medical information jewelry on their arms and hands while preparing food. Also observed several employees wearing bracelets while preparing food. 11-6-1.03(5)(j) - Hair Restraints (C) (i) Hair Restraints. 1. Employees preparing or handling food shall use effective and clean, disposable or easily cleanable nets or other hair restraints approved by the Health Authority, worn properly to restrain loose hair including beards and mustaches longer than one half inch. 2. This does not apply to employees such as counter staff who only serve beverages and wrapped or packaged foods, hostesses, and wait staff if they present a minimal risk of contaminating exposed food, clean utensils and linens and unwrapped single-service and single-use articles.

Wiping cloths: properly used and stored — Inspector Note: Observed wiping cloth bucket containing quat sanitizer did not meet the minimum required concentration of 200-400 ppm. PIC corrected on site be remaking the sanitizer. 511-6-1.04(4)(m) - Wiping Cloths, Use Limitation (C) (m) Wiping Cloths, Use Limitation. 1. Cloths in-use for wiping food spills from tableware and carry-out containers that occur as food is being served shall be: (i) Maintained dry; and (ii) Used for no other purpose. 2. Cloths in-use for wiping counters and other equipment surfaces shall be: (i) Held between uses in a chemical sanitizer solution at a concentration specified under DPH Rule 511-6-1-.05(6)(n); and (ii) Laundered daily. 3. Cloths in-use for wiping surfaces in contact with raw animal foods shall be kept separate from cloths used for other purposes. 4. Dry wiping cloths and the chemical sanitizing solutions in which wet wiping cloths are held between uses shall be free of food debris and visible soil. 5. Containers of chemical sanitizing solutions in which wet wiping cloths are held between uses shall be stored off the floor and used in a manner that prevents contamination of food, equipment, utensils, linens, single-service, or single-use articles. 6. Single-use disposable sanitizer wipes shall be used in accordance with EPA-approved manufacturer’s label use instructions.

Utensils, equipment and linens: properly stored, dried, handled — Inspector Note: Observed wet dishes stacked before being allowed to adequately air-dry. 511-6-1.05(10)(a) - Equipment & Utensils, Air-Drying Required (C) (10) Protection of Clean Items. (a) Equipment and Utensils, Air-Drying Required. After cleaning and sanitizing, equipment and utensils: 1. Shall be air-dried or used after adequate draining before contact with food; and 2. May not be cloth dried except that utensils that have been air-dried may be polished with cloths that are maintained clean and dry.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed the metal area behind the faucet in the kitchen has eroded. PIC will need to replace the faucet to prevent water from leaking on the floor. 511-6-1.05(1)(i) - Nonfood-contact Surfaces (C) (i) Nonfood-contact Surfaces. Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material.

Physical facilities installed, maintained, and clean — Inspector Note: Observed the walk in cooler floor in bad repair. 511-6-1.07(5)(a),(b) - Good Repair, physical facilities maintained; Cleaning, Frequency & Restrictions, cleaned often enough to keep them clean (C) (5) Maintenance and Operation. (a) Good Repair. All physical facilities shall be maintained in good repair. (b) Cleaning, Frequency and Restrictions. 1. The physical facilities shall be cleaned as often as necessary to keep them clean and by methods that prevent contamination of food products. 2. Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of food is exposed, such as after closing. 3. If present, playground equipment and associated areas shall be maintained in a clean and sanitary condition. In addition, a cleaning and sanitizing plan along with cleaning and sanitizing records for playground equipment and associated areas shall be maintained within the food service establishment for review upon request by the Health Authority. Further, such cleaning and sanitizing plan for employees to follow in the event of encountering vomitus or fecal matter shall be included and submitted at the time of permit application as specified in DPH Rule 511-6-1-.02(1)(c). Pf

Proper cold holding temperatures — Inspector Note: Observed a container of white gravy stored above the required temperature of 41 degrees or below. The gravy that was prepared on 8/23/26 was observed 64 degrees f. PIC corrected on site by discarding the gravy. PIC will ensure that all TCS foods area stored at 41 degrees or below. 511-6-1.04(6)(f) - Time/Temperature Control for Safety; Cold Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P

Proper cooling time and temperature — Inspector Note: Observed a container of gravy that did not meet temperature requirements during cooler. White gravy began cooing at 12:00 noon. During the audit, conducted at 3:00 pm, the white gravy was observed at 85 degrees. PIC corrected on site by discarding the gravy. PIC will coach team members on properly cooling TCS foods from 135 degrees within the first 2 hours and 70-41 degrees within 4 hours for a total of 6 hours. 511-6-1.04(6)(d) - Cooling (P) (d) Cooling. 1. Cooked time/temperature control for safety food shall be cooled: (i) Within 2 hours from 135°F (57°C) to 70°F (21°C); P and (ii) Within a total of 6 hours from 135°F (57°C) to 41°F (5°C) or less. P 2. Time/temperature control for safety food shall be cooled within 4 hours to 41°F (5°C) or less if prepared from ingredients at ambient temperature, such as reconstituted foods and canned tuna. P 3. Except as specified under paragraph 4 of this subsection, a time/temperature control for safety food received in compliance with laws allowing a temperature above 41°F (5°C) during shipment from the supplier shall be cooled within 4 hours to 41°F (5°C). P 4. Raw eggs shall be received and immediately placed in refrigerated equipment that maintains an ambient air temperature of 41°F (5°C) or less. P

Posted: Permit/Inspection/Choking Poster/Handwashing — Inspector Note: Observed the inspection score not posted at the drive thru window. Observed the inspection score in the lobby not posted within one foot reading distance. The report was printed in landscape and not portrait setting to see the entire page. 511-6-1.02(1)(d) - Displaying of the Inspection Report (C) 1. The most current inspection report shall be prominently displayed in public view at all times, within fifteen feet of the front or primary public door and between five feet and seven feet from the floor and in an area where it can be read at a distance of one foot away. 2. Food service establishments with drive-thru windows will post the current inspection report, and also have the inspection report posted so that a minimum of the top one-third of a copy of the current inspection report is visible through each window allowing customers to easily read the score, date of inspection and establishment information. 3. At food service establishments with no primary or public door, the current inspection report shall be prominently displayed at all times where the documents can be read by the public from a distance of one foot away. If requirements of this paragraph are not possible because of physical restrictions, a location will be determined as approved by the Health Authority. 4. The most current inspection report for mobile food service units and extended food service units issued by the local Health Authority having jurisdiction for its inspections shall be prominently displayed in public view during all hours of operation. Such inspection reports shall be prominently displayed at the point of service where the documents can be read by the public from a distance of one foot away. 5. A food service establishment inspection report addendum need not be displayed, but shall be made available by the food service establishment to the public upon request.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed the caulking around both 3-compartment sinks in need of removing and recaulked due to a black mold-like accumulation around the sinks. 511-6-1.05(1)(i) - Nonfood-contact Surfaces (C) (i) Nonfood-contact Surfaces. Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed the gasket in bad repair on the reach in cooler in the ice cream area. No TCS food items should be held in the reach in cooler until the gasket is replace and the cooler is at 41 or below. Currently the only thing in the reach in cooler is water and pecans. Observed the lid broken on the prep top cooler in the ice cream area. 511-6-1.05(6)(a) - Good Repair & Proper Adjustment (C) (6) Maintenance and Operation. (a) Good Repair and Proper Adjustment. 1. Equipment shall be maintained in a state of repair and condition that meets the requirements specified under subsections (1) and (2)of this Rule. 2. Equipment components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. 3. Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate food when the container is opened.

Physical facilities installed, maintained, and clean — Inspector Note: Observed damaged ceiling tiles due to water damage in the dining room in need of replacing. Observed floors in the walk in cooler with debris and the floors in the walk in freezer with ice accumulation. The floors will need to be cleaned.

Adequate ventilation and lighting; designated areas used — Inspector Note: Observed (1) light out under the ventilation hood system. 511-6-1.07(3)(f) - Lighting Intensity, adequate in food prep, storage & service areas (C) (f) Lighting Intensity. The light intensity shall be: 1. At least 10 foot candles (108 lux) at a distance of 30 inches (75 cm) above the floor, in walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning; 2. At least 20 foot candles (215 lux): (i) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption; (ii) Inside equipment such as reach-in and under-counter refrigerators; (iii) At a distance of 30 inches (75 cm) above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms; and 3. At least 50 foot candles (540 lux) at a surface where a food service employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.

Adequate ventilation and lighting; designated areas used — Inspector Note: Observed a mold like accumulation on the HVAC vent in front of the ice machine in the kitchen.

Food-contact surfaces: cleaned & sanitized — Inspector Note: Observed both 3-compartment sinks sanitizer hoses not working properly to dispense the sanitizer solution properly. Advised PIC to make the sanitizer manually to avoid not washing dishes properly. Sanitizer was made manually at 200 PPM quaternary ammonium solution (COS). Ecolab will need to be called to service both sinks. A detailed work order will need to be emailed to [REDACTED EMAIL] by 2/10/26 showing that the hoses and sanitizer has been repaired. In the ice cream area the sanitizer and detergent hoses are leaking and needs to be adjusted. 511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows: 1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P Concentration Range Minimum Temperature MG/L PH 10 or less oF (oC) PH 8 or less oF (oC) 25-49 120 (49) 120 (49) 50-99 100 (38) 75 (24) 100 55 (13) 55 (13) 2. An iodine solution shall have a minimum temperature of 68°F (20°C)P minimum concentration between 12.5 ppm and 25 ppm, P and pH of 5.0 or less or a pH no higher than the level for which the manufacturer specifies for the solution to be effective; P 3. A quaternary ammonium compound solution shall have a minimum temperature of 75ºF (24ºC), P have a concentration as specified in DPH Rule 511-6-1-.07(6)(g) and as indicated by the manufacturer’s use directions included in the labeling, P and be used only in water with 500 ppm hardness or less or in water having a hardness no greater than specified by the EPA-registered label use instructions; P 4. If another solution of a chemical specified under paragraphs 1 through 3 of this subsection is used, the permit holder shall demonstrate to the Health Authority that the solution achieves sanitization and the use of the solution shall be approved; P 5. If a chemical sanitizer other than chlorine, iodine, or a quaternary ammonium compound is used, it shall be applied in accordance with the EPA-registered label use instructions ;P and 6. If a chemical sanitizer is generated by a device located on-site at the food service establishment, it shall be used as specified in 1-5 of this subsection and shall be produced by a device that: (i) complies with law as specified in sections 2(q)(1) and 12 of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), P (ii) complies with 40 CFR 152.500 Requirement for Devices and 40 CFR 156.10 Labeling Requirements, P (iii) displays the EPA device manufacturing facility registration number on the device, Pf and (iv) is operated and maintained in accordance with manufacturer’s instructions. Pf. 7. On-site chemical sanitizer generating equipment with active ingredients, such as copper, must be registered as pesticides. The active ingredient may be part of the equipment or separately added.

Food-contact surfaces: cleaned & sanitized — Inspector Note: Observed the lid over the ice machine in need of cleaning (drive thru) area.

Toxic substances properly identified, stored, used — Inspector Note: Observed propane refrigerator gas (chemical) stored on the prep surface in the kitchen. PIC stated that it had been there since yesterday. He stated that someone was working on their reach in cooler that is currently out. All chemicals should be stored in a designated area (COS). 511-6-1.07(6)(c) - Storage, Separation (P) (c) Storage, Separation. Poisonous or toxic materials shall be stored so they cannot contaminate food, equipment, utensils, linens, and single-service and single-use articles by: 1. Separating the poisonous or toxic materials by spacing or partitioning; P and 2. Locating the poisonous or toxic materials in an area that is not above food, equipment, utensils, linens, and single-service or single-use articles. This requirement does not apply to equipment and utensil cleaners and sanitizers that are stored in warewashing areas for availability and convenience if the materials are stored to prevent contamination of food, equipment, utensils, linens, and single-service and single-use articles. P