Bombay Bites

In-use utensils: properly stored — Inspector Note: Observed the ice bin bucket stored on the floor in the bar area. PIC corrected on site be removing the ice bucket off the floor. Cups observed being used to scoop sauce in the walk in cooler and rice did not contain a handle. PIC instructed to use a scoop with a handle. 511-6-1.04(4)(k) - In-Use Utensils, Between-Use Storage (C) (k)Storage of In-Use Utensils. During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: 1.Except as specified under paragraph 2 of this subsection, in the food with their handles above the top of the food and the container; 2.In food that is not time/temperature control for safety food with their handles above the top of the food within containers or equipment that can be closed, such as bins of sugar, flour, or cinnamon; 3.On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized at a frequency specified under DPH Rule 511-6-1-.05(7)(b) and (8)(a); 4.In running water of sufficient velocity to flush particulates to the drain, if used with moist food such as ice cream or mashed potatoes; 5. In a clean, protected location if the utensils, such as ice scoops, are used only with a food that is not time/temperature control for safety food; or 6. In a container of water if the water is maintained at a temperature of at least 135°F (57°C) and the container is cleaned at a frequency specified under DPH Rule 511-6-1-.05(7)(b)3(vi).

Utensils, equipment and linens: properly stored, dried, handled — Inspector Note: Observed wet dishes stored improperly after washing. All clean dishes must air dried prior to stacking. Dishes and utensils cannot be stored wet prior to being allowed to air dry. 511-6-1.05(10)(a) - Equipment & Utensils, Air-Drying Required (C) (10) Protection of Clean Items. (a) Equipment and Utensils, Air-Drying Required. After cleaning and sanitizing, equipment and utensils: 1. Shall be air-dried or used after adequate draining before contact with food; and 2. May not be cloth dried except that utensils that have been air-dried may be polished with cloths that are maintained clean and dry.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed fryer basket skimmers contained broken wires PIC corrected on site by discarding the fryer basket skimmers. PIC will replace the oven cover by 8/13/26. Also observed cutting boards in bad repair. PIC will replace cutting boards that are stained or contain deep cuts. 511-6-1.05(2)(c) - Multiuse Food-Contact Surfaces (Pf) (c) Multiuse Food-Contact Surfaces. 1. Multiuse food-contact surfaces shall be: (i) Smooth; Pf (ii) Free of breaks, open seams, cracks, chips, inclusions, pits, and similar imperfections; Pf (iii) Free of sharp internal angles, corners, and crevices; Pf (iv) Finished to have smooth welds and joints; Pf and (v) Except as specified in paragraph 2 of this subsection, accessible for cleaning and inspection by one of the following methods: (I) Without being disassembled, Pf (II) By disassembling without the use of tools, Pf or (III) By easy disassembling with the use of handheld tools commonly available to maintenance and cleaning personnel such as screwdrivers, pliers, open-end wrenches, and Allen wrenches. Pf 2. The requirement in paragraph 1(v) of this subsection does not apply to cooking oil storage tanks, Distribution lines for cooking oils, or beverage syrup lines or tubes. 511-6-1.05(6)(b) - Cutting Surfaces (C) (b) Cutting Surfaces. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced

Plumbing installed; proper backflow devices — Inspector Note: Observed a condensation leak in the walk in cooler. A pan of water was observed on the shelf below the condensation leak. Also observed a leak in the bottom of the preparation/sandwich cooler due to the cooler maintaining an ambient air temperature of 50 degrees. PIC instructed to remove food items from below the condensation leak until repairs are completed. PIC will also cease using the sandwich cooler. PIC will email a copy of the completed work order to [REDACTED EMAIL] and [REDACTED EMAIL] by 8/15/2026

Garbage/refuse properly disposed; facilities maintained — Inspector Note: Observed trash build up in the dumpster area. PIC advised that multiple tenants in the strip mall are using the dumpster.. 511-6-1.06(5)(o),(p) - Using Drain Plugs; Maintaining Refuse Areas (C) (o) Using Drain Plugs. Drains in receptacles and waste handling units for refuse, recyclables, and returnables shall have drain plugs in place. (p) Maintaining Refuse Areas and Enclosures. A storage area and enclosure for refuse, recyclables, or returnables shall be maintained free of unnecessary items and clean.

Physical facilities installed, maintained, and clean — Inspector Note: Floor grout missing between tile in front of the three compartment sink. Also observed floor tile in bad repair/missing in the dining area. PIC advised that he is repairing/replacing tile in the dining area by 8/14/26. Kitchen tile must be regrouted by 8/20/26

Food separated and protected — Inspector Note: Observed raw shelled eggs stored above sauce in the walk in cooler. Also observed raw chicken stored next to peppers in the walk in cooler. Raw chicken was stored next to cooked chicken in the reach in cooler. Raw chicken above cheese in the reach in cooler. 511-6-1.04(4)(c)1(i)(ii)(iii)(v)(vi)(vii)(viii) - Packaged & Unpackaged Food Separation, Packaging, and Segregation (P, C) (c) Packaged and Unpackaged Food - Separation, Packaging, and Segregation. 1. Food shall be protected from cross contamination by: (i) Except as specified in paragraph (i)(IV) of this subsection, separating raw animal foods during storage, preparation, holding, and display from: (I) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, P and (II) Cooked ready-to-eat food; and P (III) Fruits and vegetables before they are washed; P (IV) Frozen, commercially processed and packaged raw animal food may be stored or displayed with or above frozen, commercially processed and packaged, ready-to-eat food. (ii) Except when combined as ingredients, separating types of raw animal foods from each other such as beef, fish, lamb, pork, and poultry during storage, preparation, holding, and display by: (I) Using separate equipment for each type, P or (II) Arranging each type of food in equipment so that cross contamination of one type with another is prevented, P and (III) Preparing each type of food at different times or in separate areas; P (iii) Cleaning and sanitizing equipment and utensils; (v) Cleaning hermetically sealed containers of food of visible soil before opening; (vi) Protecting food containers that are received packaged together in a case or overwrap from cuts when the case or overwrap is opened; (vii) Storing damaged, spoiled, or recalled food being held in the food service establishment separate from food, equipment, utensils, linens and single-service and single-use articles; or (viii) Separating fruits and vegetables, before they are washed from ready-to-eat food.

Proper cold holding temperatures — Inspector Note: Observed TCS foods (Raw chicken), mozzarella cheese, and diced cheese stored above the requirement temperature of 41 degrees or below. TCS foods were stored at 50 degrees or above. Sauce was observed at 45 degrees. The ambient air temperature of the prep top cooler was 50 degrees. PIC will replace the cooler by 8/15/26

Wiping cloths: properly used and stored — Inspector Note: Observed wiping cloth bucket sanitizing solution was observed above 200 ppm. PIC corrected on site by remaking the sanitizer buckets. Once corrected, the wiping cloth sanitizer buckets were observed at 50 ppm. 511-6-1.04(4)(m) - Wiping Cloths, Use Limitation (C) (m) Wiping Cloths, Use Limitation. 1. Cloths in-use for wiping food spills from tableware and carry-out containers that occur as food is being served shall be: (i) Maintained dry; and (ii) Used for no other purpose. 2. Cloths in-use for wiping counters and other equipment surfaces shall be: (i) Held between uses in a chemical sanitizer solution at a concentration specified under DPH Rule 511-6-1-.05(6)(n); and (ii) Laundered daily. 3. Cloths in-use for wiping surfaces in contact with raw animal foods shall be kept separate from cloths used for other purposes. 4. Dry wiping cloths and the chemical sanitizing solutions in which wet wiping cloths are held between uses shall be free of food debris and visible soil. 5. Containers of chemical sanitizing solutions in which wet wiping cloths are held between uses shall be stored off the floor and used in a manner that prevents contamination of food, equipment, utensils, linens, single-service, or single-use articles. 6. Single-use disposable sanitizer wipes shall be used in accordance with EPA-approved manufacturer’s label use instructions.

Utensils, equipment and linens: properly stored, dried, handled — Inspector Note: Observed wet dishes stored improperly after washing. All clean dishes must air dried prior to stacking. Dishes and utensils cannot be stored wet prior to being allowed to air dry. 511-6-1.05(10)(a) - Equipment & Utensils, Air-Drying Required (C) (10) Protection of Clean Items. (a) Equipment and Utensils, Air-Drying Required. After cleaning and sanitizing, equipment and utensils: 1. Shall be air-dried or used after adequate draining before contact with food; and 2. May not be cloth dried except that utensils that have been air-dried may be polished with cloths that are maintained clean and dry.

Insects, rodents, and animals not present — Inspector Note: Observed multiple fly strips hanging throughout the kitchen area. All strips were filled with dead flies. PIC immediately corrected on site by removing and discarding all fly strips. PIC will use the vector control lights to control flies. 511-6-1.07(5)(k) - Controlling Pests (Pf, C) 511-6-1.07(2)(k) - Insect Control Devices (C) (k) Insect Control Devices, Design and Installation. 1. Insect control devices that are used to electrocute or stun flying insects shall be designed to retain the insect within the device. 2. Insect control devices shall be installed so that: (i) The devices are not located over a food preparation area; and (ii) Dead insects and insect fragments are prevented from contact with exposed food; clean equipment, utensils, and linens; and unwrapped single-service and single-use articles.

Proper eating, tasting, drinking, or tobacco use — Inspector Note: Observed employee food stored in the food preparation. The food was being consumed. The meal was partially consumed with a spoon observed on the plate. PIC corrected on site by discarding the food. There was also an employee drink stored in the reach in freezer. 511-6-1.03(5)(k)1&2 - Eating, Drinking, or Using Tobacco (C) (k) Hygienic Practices. 1. Employees shall not use any form of tobacco products, or electronic devices that simulate tobacco smoking, while engaged in food preparation or service, nor while in areas used for equipment or utensil washing and storage, food preparation or food storage. Employees shall only use tobacco products or electronic devices that simulate tobacco smoking in approved designated areas. 2. Employees shall consume food only in approved designated areas separate from food preparation and serving areas, equipment or utensil areas and food storage areas. However, drinking from a single service beverage cup with a secure lid and straw that is handled to prevent contamination of the employee’s hands, the container, exposed food, clean equipment, utensils and linens, unwrapped single-service and single-use articles will be allowed.

Food separated and protected — Inspector Note: Observed raw chicken stored above a container of cooked vegetables (Chickpeas) in the walk in cooler. PIC corrected on site by properly storing all cooked and raw TCS foods in the walk in cooler. PIC also educated team members on the proper way to store food items in the walk in cooler. PIC used the food safety storage chart located on the walk in cooler door to educate employees. 511-6-1.04(4)(c)1(i)(ii)(iii)(v)(vi)(vii)(viii) - Packaged & Unpackaged Food Separation, Packaging, and Segregation (P, C) (c) Packaged and Unpackaged Food - Separation, Packaging, and Segregation. 1. Food shall be protected from cross contamination by: (i) Except as specified in paragraph (i)(III) of this subsection, separating raw animal foods during storage, preparation, holding, and display from: (I) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, P and (II) Cooked ready-to-eat food; and P (III) Frozen, commercially processed and packaged raw animal food may be stored or displayed with or above frozen, commercially processed and packaged, ready-to-eat food. (ii) Except when combined as ingredients, separating types of raw animal foods from each other such as beef, fish, lamb, pork, and poultry during storage, preparation, holding, and display by: (I) Using separate equipment for each type, P or (II) Arranging each type of food in equipment so that cross contamination of one type with another is prevented, P and (III) Preparing each type of food at different times or in separate areas; P (iii) Cleaning and sanitizing equipment and utensils; (v) Cleaning hermetically sealed containers of food of visible soil before opening; (vi) Protecting food containers that are received packaged together in a case or overwrap from cuts when the case or overwrap is opened; (vii) Storing damaged, spoiled, or recalled food being held in the food service establishment separate from food, equipment, utensils, linens and single-service and single-use articles; or (viii) Separating fruits and vegetables, before they are washed from ready-to-eat food.

Food-contact surfaces: cleaned & sanitized — Inspector Note: Observed the chlorine sanitizer in the three compartment sink exceeded the required concentration of 50-100 ppm. The sanitizer was observed above 200 ppm. PIC corrected on site my remaking the sanitizer. Once corrected, the sanitizer was observed at 50 ppm. PIC will coach/train all team members on properly measuring the sanitizer. 511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows: 1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P Concentration Range Minimum Temperature MG/L PH 10 or less oF (oC) PH 8 or less oF (oC) 25-49 120 (49) 120 (49) 50-99 100 (38) 75 (24) 100 55 (13) 55 (13) 2. An iodine solution shall have a minimum temperature of 68°F (20°C)P minimum concentration between 12.5 ppm and 25 ppm, P and pH of 5.0 or less or a pH no higher than the level for which the manufacturer specifies for the solution to be effective; P 3. A quaternary ammonium compound solution shall have a minimum temperature of 75ºF (24ºC), P have a concentration as specified in DPH Rule 511-6-1-.07(6)(g) and as indicated by the manufacturer’s use directions included in the labeling, P and be used only in water with 500 ppm hardness or less or in water having a hardness no greater than specified by the EPA-registered label use instructions; P 4. If another solution of a chemical specified under paragraphs 1 through 3 of this subsection is used, the permit holder shall demonstrate to the Health Authority that the solution achieves sanitization and the use of the solution shall be approved; P 5. If a chemical sanitizer other than chlorine, iodine, or a quaternary ammonium compound is used, it shall be applied in accordance with the EPA-registered label use instructions ;P and 6. If a chemical sanitizer is generated by a device located on-site at the food service establishment, it shall be used as specified in 1-5 of this subsection and shall be produced by a device that: (i) complies with law as specified in sections 2(q)(1) and 12 of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), P (ii) complies with 40 CFR 152.500 Requirement for Devices and 40 CFR 156.10 Labeling Requirements, P (iii) displays the EPA device manufacturing facility registration number on the device, Pf and (iv) is operated and maintained in accordance with manufacturer’s instructions. Pf. 7. On-site chemical sanitizer generating equipment with active ingredients, such as copper, must be registered as pesticides. The active ingredient may be part of the equipment or separately added.

Proper date marking and disposition — Inspector Note: 6-2. Observed prepared TCS foods in the walk in cooler not marked with date of preparation or date for disposal. Also observe Tzatziki sauce and Masala not date marked. PIC will ensure that all TCS foods are properly labeled and date marked. 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking 1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 5 and 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf 2. Except as specified in paragraphs 5 through 7 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf 3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf 4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include: (i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine; (ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; (iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or