Bojangles #1275

Personal cleanliness — Inspector Note: Observed an employee working in the kitchen with jewelry (Rings with stones). 511-6-1.03(5)(g) - Jewelry (C) (g) Jewelry. Except for a plain ring such as a wedding band food employees may not wear jewelry including medical information jewelry on their arms and hands while preparing food.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed protective material not removed from the exterior of the pass thru warmer. Dust accumulation was observed on top of the warmer. PIC remove the plastic protection covering by 7/24/2026. 511-6-1.05(1)(i) - Nonfood-contact Surfaces (C) (i) Nonfood-contact Surfaces. Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material.

Nonfood-contact surfaces clean — Inspector Note: Observed white build up on pans in the storage area. PIC will have the pans cleaned by 7/23/26.

Physical facilities installed, maintained, and clean — Inspector Note: Observed stagnant water on the floor in front of the walk in freezer. 511-6-1.07(5)(a),(b) - Good Repair, physical facilities maintained; Cleaning, Frequency & Restrictions, cleaned often enough to keep them clean (C) (5) Maintenance and Operation. (a) Good Repair. All physical facilities shall be maintained in good repair. (b) Cleaning, Frequency and Restrictions. 1. The physical facilities shall be cleaned as often as necessary to keep them clean and by methods that prevent contamination of food products. 2. Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of food is exposed, such as after closing. 3. If present, playground equipment and associated areas shall be maintained in a clean and sanitary condition. In addition, a cleaning and sanitizing plan along with cleaning and sanitizing records for playground equipment and associated areas shall be maintained within the food service establishment for review upon request by the Health Authority. Further, such cleaning and sanitizing plan for employees to follow in the event of encountering vomitus or fecal matter shall be included and submitted at the time of permit application as specified in DPH Rule 511-6-1-.02(1)(c). Pf

Adequate ventilation and lighting; designated areas used — Inspector Note: Observed ceiling vent paint peeling in the walk in freezer area. PIC will have the vent cover replaced by 7/24/2026.

Single-use/single-service articles: properly stored, used — Inspector Note: Observed single use/single service bowls stored in the dry storage area not protected from contamination. PIC removed the bowls and covered them (COS). 511-6-1.05(10)(e)1&3 - Single-Service/Single-Use items stored 6" off floor in clean, dry location (C) (e) Equipment, Utensils, Linens, and Single-Service and Single-Use Articles. 1. Except as specified in paragraph 4 of this subsection, cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (i) In a clean, dry location; (ii) Where they are not exposed to splash, dust, or other contamination; and (iii) At least 6 inches (15 centimeters) above the floor. 3. Single-service and single-use articles shall be stored as specified under paragraph 1 of this subsection and shall be kept in the original protective package or stored by using other means that afford protection from contamination until used.

Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used — Inspector Note: Observed two brushes for the butter in bad repair and in need of replacing to avoid contamination of food items. 511-6-1.05(2)(c) - Multiuse Food-Contact Surfaces (Pf) (c) Multiuse Food-Contact Surfaces. 1. Multiuse food-contact surfaces shall be: (i) Smooth; Pf (ii) Free of breaks, open seams, cracks, chips, inclusions, pits, and similar imperfections; Pf (iii) Free of sharp internal angles, corners, and crevices; Pf (iv) Finished to have smooth welds and joints; Pf and (v) Except as specified in paragraph 2 of this subsection, accessible for cleaning and inspection by one of the following methods: (I) Without being disassembled, Pf (II) By disassembling without the use of tools, Pf or (III) By easy disassembling with the use of handheld tools commonly available to maintenance and cleaning personnel such as screwdrivers, pliers, open-end wrenches, and Allen wrenches. Pf 2. The requirement in paragraph 1(v) of this subsection does not apply to cooking oil storage tanks, Distribution lines for cooking oils, or beverage syrup lines or tubes.

Nonfood-contact surfaces clean — Inspector Note: Observed the exterior surface behind the drink nozzles in need of replacing due to a mold like substance. Observed the exterior surface (double lid) of the ice cover in need of cleaning due to a brown build up. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. 3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Physical facilities installed, maintained, and clean — Inspector Note: Observed the floor in need of cleaning underneath the reach in cooler that is not in use. Observed the ceiling tile with build up in the dry storage area, dining room (by drink machine), and in the kitchen above the steam table. 511-6-1.05(6)(a) - Good Repair & Proper Adjustment (C) (6) Maintenance and Operation. (a) Good Repair and Proper Adjustment. 1. Equipment shall be maintained in a state of repair and condition that meets the requirements specified under subsections (1) and (2)of this Rule. 2. Equipment components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. 3. Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate food when the container is opened.